Air Fuel Ratio Calculator
Calculate the air-to-fuel ratio from measured air and fuel mass per engine cycle. Enter both quantities in the same mass unit to get a dimensionless ratio.
Calculators
Decision-support tools for sizing, cost, capacity, runtime, ownership, and other practical planning questions.
Calculate the air-to-fuel ratio from measured air and fuel mass per engine cycle. Enter both quantities in the same mass unit to get a dimensionless ratio.
Estimate the minimum alternator output needed to support the combined electrical load at a chosen engine speed, with an adjustable reserve margin. This arithmetic estimate does not confirm vehicle fitment or alternator performance.
Estimate the board-foot volume of lumber from its thickness, width, length, and piece count. Enter dimensions in inches and quantity in whole pieces.
Estimate brake pad replacement cost by multiplying the number of pads by the cost per pad, then adding labor hours multiplied by the hourly labor rate. This estimate assumes the entered pad count covers the selected axles and excludes taxes, fees, and additional parts or repairs.
Estimate camshaft valve overlap in crankshaft degrees using intake duration, exhaust duration, and lobe separation angle. This calculation assumes valve durations are measured at the same checking lift and uses symmetrical cam lobes.
Estimate the fuel cost of a trip from trip distance, vehicle fuel economy, and fuel price. Enter distance and fuel economy in matching units, such as miles and miles per gallon or kilometers and liters per 100 kilometers.
Estimate the mileage charge for miles driven beyond a lease allowance by multiplying excess miles by the charge per mile. Enter the excess mileage and the per-mile rate stated in your lease documents.
Estimate the monthly principal-and-interest payment for a car loan using the amount financed, annual interest rate, and loan term. The estimate excludes taxes, fees, insurance, and other ownership costs.
Estimate annual routine car maintenance costs from your yearly mileage, service frequency, oil service cost, tire service cost, and other planned maintenance. The estimate uses the costs and schedule you enter and does not predict repairs.
Estimate concrete volume for a rectangular slab from its length, width, thickness, and a chosen waste allowance. The result is shown in cubic yards.
Estimate the linear feet of decking boards needed to cover a rectangular deck, including a user-selected allowance for cutting waste. Assumes boards run along the deck length and uses board face width plus gap as the coverage per row.
Calculate axle differential ratio from driveshaft and wheel rotation counts using a direct mechanical measurement. Enter the number of driveshaft turns and wheel turns observed during the test.
Estimate driveshaft speed in revolutions per minute from engine RPM, transmission gear ratio, and axle ratio. The calculation assumes a direct mechanical connection through the selected gear and does not account for clutch slip or torque converter slip.
Estimate drywall sheets and joint compound from room dimensions, openings, board size, and a stated waste allowance. This is a materials planning estimate and does not assess structural requirements or installation conditions.
Estimate a practical riding distance from battery capacity, average energy use, and the share of the battery you plan to use. The result is a planning estimate; actual range varies with conditions and riding style.
Estimate the electricity cost of charging for a regular commute using your daily round-trip distance, vehicle energy use, electricity price, and commuting days per week.
Calculate an engine's geometric displacement from bore, stroke, and cylinder count. Use the same length unit for bore and stroke. The result is in the cube of that unit.
Estimate a cylinder's static compression ratio from swept volume, combustion-chamber volume, piston dish or dome volume, head-gasket volume, and deck-clearance volume. Enter piston dish and other added volumes as positive values and piston dome volume as a negative value. This simplified geometric estimate does not account for dynamic compression or engine-specific measurement uncertainty.
Calculate geometric engine displacement from cylinder bore, stroke, and cylinder count. Enter bore and stroke in the same length unit to get displacement in the corresponding cubic unit.
Estimate engine horsepower from torque in pound-feet and engine speed in revolutions per minute using the standard 5,252 conversion constant.
Estimate theoretical engine RPM from road speed, tire circumference, transmission ratio, and final-drive ratio. Assumes no tire or drivetrain slip and excludes torque-converter slip.
Estimate fuel economy from the distance traveled and fuel used. The result is distance per unit of fuel, using the units you enter.
Estimate injector duty cycle from the total fuel flow demand and the flow rating of one injector. This simple ratio assumes demand is shared evenly across identical injectors.
Estimate a gasoline engine's minimum fuel pump flow requirement from engine power, brake-specific fuel consumption, fuel density, and a sizing margin. This worksheet assumes the supplied power and BSFC apply at the intended operating point and does not account for pump output loss at operating pressure or voltage.
Calculate the approximate interior volume of a garage in cubic feet by multiplying its length, width, and height. Enter all dimensions in feet. The estimate assumes a simple rectangular space and does not account for obstructions or irregular areas.
Calculate the overall gear reduction from a transmission gear ratio and axle ratio, with an optional transfer-case ratio for four-wheel-drive gearing. The result is the number of driveshaft revolutions per wheel revolution in the selected gearing.
Estimate the volume of gravel needed to cover a rectangular area at a chosen depth. The result is the geometric volume in cubic yards and does not include compaction, settling, or delivery allowances.
Estimate engine horsepower from torque and engine speed using the standard mechanical horsepower relationship. Enter torque in pound-feet and engine speed in revolutions per minute. The result is a mathematical estimate and does not account for drivetrain loss or measurement conditions.
Convert mechanical horsepower into kilowatts using the standard factor of 0.745699872 kilowatts per horsepower. Enter a horsepower value to see its equivalent power in kilowatts.
Compare estimated annual fuel costs for a hybrid and a conventional vehicle using your annual distance, each vehicle's fuel economy, and your local fuel price. The estimate covers fuel only and assumes the entered distance and fuel price stay constant.
Calculate total linear feet by multiplying a measured length by the number of matching pieces. Enter length in feet and inches, then review the total in feet.
Estimate a planning interval in miles by adjusting a baseline interval for your driving conditions. This is a worksheet estimate, not a substitute for your vehicle maker’s maintenance schedule.
Estimate the total paint volume needed for a project from the surface area, number of coats, and product coverage rate. This worksheet-style estimate assumes the entered coverage applies evenly to each coat and does not include extra paint for waste, texture, or touch-ups.
Estimate piston compression height from deck height, crankshaft stroke, and connecting rod length using consistent millimeter measurements. The formula assumes deck height is measured from the crankshaft centerline to the block deck and calculates the nominal distance from the piston pin center to the piston crown reference point.
Estimate average piston speed from engine stroke and crankshaft speed. The result is a kinematic calculation based on the supplied dimensions and RPM, not a complete engine durability assessment.
Calculate a vehicle's power-to-weight ratio from its engine power and total vehicle weight. Enter horsepower and pounds to see horsepower per 1,000 pounds.
Estimate quarter-mile elapsed time from vehicle race weight and quarter-mile trap speed using a simplified empirical model. Enter weight in pounds and trap speed in miles per hour.
Estimate a vehicle’s rear axle ratio by dividing driveshaft revolutions by wheel revolutions during a controlled rotation check. The result is a measurement-based estimate and does not identify the axle or verify its factory specification.
Calculate roof pitch as a rise-to-run ratio and percentage from measured vertical rise and horizontal run. The result describes the measured slope and does not determine whether a roof is safe to access or suitable for construction.
Calculate floor area in square feet from room dimensions. Enter the length and width of each rectangular area and add the areas together for a total.
Estimate tile area, add a configurable waste allowance, and calculate the number of tiles to order from room dimensions and tile size. This planning estimate assumes a rectangular room and consistent tile coverage.
Estimate a tire's pressure change from a temperature change using the ideal-gas relationship, assuming tire volume stays constant and gauge pressure is referenced to standard atmospheric pressure.
Estimate a tire's nominal overall diameter in inches from its section width, aspect ratio, and wheel diameter.
Convert engine torque and rotational speed into estimated horsepower using the standard mechanical horsepower relationship. Enter torque in pound-feet and engine speed in revolutions per minute.
Estimate your vehicle's operating cost per mile by combining fuel, maintenance, and other trip expenses, then dividing by miles driven. Use your own figures to plan commute costs; this is a simple worksheet estimate, not a prediction of future costs.
Calculate the observed percentage change between a vehicle’s purchase price and its current resale value. This arithmetic estimate uses the values you enter and does not forecast market prices.
Estimate walking time from route distance and your chosen walking pace. The result assumes a steady pace and does not account for stops, terrain, or delays.
Estimate the number of wallpaper rolls needed from room dimensions, roll coverage, and a waste allowance. This is a coverage estimate and does not account for pattern matching or unusual wall layouts.
Convert a wheel bolt circle diameter (PCD) between inches and millimeters. Keep the lug count unchanged and pair it with the converted diameter when reading or recording a bolt pattern.
Calculate a wheel's estimated offset in millimeters from backspacing and overall wheel width measured lip-to-lip on the same wheel. The signed result is an arithmetic conversion, not fitment advice.